Відео

How much did you charge for this sign?

This does not work for changing lines on a Danby Dual Tap completely different

Great demonstration of how to do this! Thanks for sharing

Thank you for this very good and clear video. I am still learning my way around CNC and am getting ready to cut some big sheets, so tiling and registration are interesting to me. Some of my planned big sheets have many parts. I ran a test recently using tabs to hold the many parts together so holding the sheet is less critical. I made the tabs about half the thickness of the material. This allows a router with a 1/4" trim bit (with a ball bearing) to guide the bit along the half-cut depth while cleanly cutting away the tab. This works very well and requires little finishing. Thanks again for your video!

May I ask what colors did you use for the blue and gray?

Good job! It doesn't get any simpler than that! No videos in 3 years? What a shame!

What is the insert size?

I have issues after buying my last 2 hot ends, back to back

What (minimum) saw height does the bandsaw must be to mill lumber?

Could you make templates to use with bandsaw and router for those of us that don't CNC ?

anddd I just bought the longest largest drawer slides ever.

Flat sawn warpy cupping wood.

Awesome video, easy to follow. That kit is awesome and super simple!! Cheers

Congratuletion

do you open that ball valve on the gas line before you tap the keg or after? Thanks

Do c02 lines need cleaning?

Haha, my dust collector uses a similar Alexa "plug-in". I'm planning floor space and only have room for a 48x24 or a 30x30 cutting size...an extra indexing vs wider stock...what are your thoughts from a sign making perspective? Should a residential small home business even worry about 4' wide signs? Thanks for any help you can offer.

I'm shopping for a band saw right away

Great budget bandsaw

Siri did the job!

?????

What psi your co2 set at? TIA

Funny thing is I need to know how you got that shank nut off. Cause I have no idea

Noticed you have 2 small wooden pieces at the bottom of your kegerator, what is this used for?

I really hope this is staged because no way people are this dumb

I still have it!

Great video@

This was a fun video! I have a bandsaw on the way... "smaller" than yours, but I plan to hit the wood racks outside and not BUY wood! I'd rather spend it on tools! Thanks for sharing!

Def wear gloves y'all! That powder may not look as caustic as the green glow the pros use, but trust you do not want it in your cuticles. 🙏

never one guy pushing and another pulling at the same time.the pulling may not be expected by the pusher and his fingers may be at the receiving end , sadly.

We love em!!

Good video on cleaning your lines. If you don't have that neat springy tool/ball...coupler holder thing @ 4:10 don't fret...Just use a bar or soft drink straw. Just stick it up into the coupler a bit....then set it down carefully in the basin. That straw will prevent the check ball from blocking the cleaning & rinsing liquids. I have an older Perlick tap faucet that has two small almost hidden vent holes or channels that sometimes plug up with....crud once in a while. I just use a straight twist tie to open up the passages. (All faucets may not have these) It took me about a year to eventually realizing these plugged holes were to blame for my foamy pours. Just some fyi. This cleaning can be a pain to have to do all the time...very tempting to just say..."I'll clean the lines on the next keg change." But doing this on a regular schedule really makes a difference on how your brew tastes & how it pours. It's well worth the time & effort. Cheers.

Great video. I have a ton of Honey Locust which has a beautiful core that I was wanting to cut like this.

Those cleaning kits are 30. A new top with one pull down and a new hose is 30 lol. I bought a new kit with two pull downs and both hoses for 60. Not sure why you'd spend the time cleaning something when you can just replace everything you're cleaning for the same price.

😂 😂 😂 😂 😂 😂 😂 😂 😂 😂 😂

Did you sand the texture at all or did you use a finishing wheel of some sort to get the fuzzies off? I am looking for a way to easily remove most of the fuzz from the sign I made using your instructions here.

How frequently should you do this?

I had the same reaction when I priced a cnc machine.

Is that wood ash, or is it willow?

Great video my friend. Thanks for the tip not to get the wife angry lol. Merry Christmas.

Do you unplug it during this process?

Is the cnc file available

Good stuff. You have a new subscriber.

Awesome job!!

Thank you brother.. I just learned how to Mill Woods...

This is great! I would have liked to see more of the business-side of it, as the title suggests.. plus the cookie cutter actually being used would be nice. Thanks for the video!

menos musica y mas explicacion

Good video. But..... get a kit with a hand pump yall.

Love this. What are you sealing the ends with?

the crest in the center does not come out what am I doing wrong? when running all the trajectories it does not come out...